★Carried & Installed
Yamaha receivers · Kansas City.
IntegrateIT carries and installs Yamaha audio across the Kansas City metro — the AV receiver at the centre of a media room, the network hi-fi receiver in a listening room, and MusicCast putting the same music in the kitchen and on the patio. This page is about Yamaha’s home audio, not its instruments. One precision first, because the trade is sloppy about this word: Yamaha is a line we carry and install under distribution, not one we hold our own dealer agreement on, so we do not call ourselves an authorized Yamaha dealer. What we are is the people who count the channels, place the speakers, wire the room, bring the receiver under the control system and calibrate it afterwards. Phone: (913) 804-7575 or office@integrateit.tech.
What we carry and install from Yamaha
Yamaha’s own hub describes its home audio as AV receivers, hi-fi receivers, integrated amplifiers, wireless speakers and the MusicCast system that ties them together. The models below are the ones its guides name, with its own channel counts. We specify, install and commission to order.
- AV receivers. Yamaha’s AV receiver guide covers the RX-V4A at 5.2 channels, the RX-V6A at 7.2 and the RX-V8A at 11.2. It lists Dolby Atmos and DTS:X on all three and a second zone on the RX-V6A and RX-V8A; a Zone 2 patio system is the example it gives. For a media room or a Dolby Atmos theater, the choice follows the speaker count.
- YPAO room optimization. Yamaha describes YPAO, the Yamaha Parametric room Acoustic Optimizer, as analyzing the room’s acoustics. On a multichannel receiver it matches the speakers to a target curve; on a two-channel hi-fi receiver it matches the two speakers to each other; and Yamaha says it favors cutting frequencies over boosting them. We run it, then check the result by ear in our calibration pass.
- Network hi-fi receivers. The R-N600A, R-N800A, R-N1000A and R-N2000A are stereo receivers that Yamaha lists with MusicCast, Bluetooth, AirPlay 2 and streaming from services such as Spotify and Amazon Music HD. The R-N800A lists YPAO, and the R-N1000A adds HDMI ARC for a television. Yamaha also describes a USB DAC section in its network receivers, and its article names the R-N800A, R-N1000A and R-N2000A.
- Integrated amplifiers. Yamaha’s guide names the A-S3200, A-S2200 and A-S1200. An integrated amplifier combines the preamplifier, the power amplifier, phono equalization and tone controls in one component. Yamaha says the A-S3200 can switch between two sets of speakers in two rooms, and that its Pre Out lets it act as a preamplifier alone so a separate power amplifier can be added.
- MusicCast. Yamaha’s whole-house system shares music over your existing Wi-Fi network to any MusicCast-enabled component. The free MusicCast Controller app handles rooms, linked zones and Routines, which are whole-home presets that include a factory one to shut every device down when you leave. The MusicCast 20 and MusicCast 50 wireless speakers can also serve as rear surrounds with a compatible Yamaha AV receiver. It is one way we build whole-house audio.
- Install amplifiers and streamers. Yamaha’s article on residential, commercial and mixed-use installations names the AVENTAGE RX-A8A as the receiver in a residential system, and the XDA-QS5400RK Quad Streamer, the XMV8280 power amplifier and the MA2030a amplifier among its install products. It gives coffee shops and small restaurants as examples of the hybrid space between the two.
How we put a Yamaha receiver into a room
- Channels from the speaker layout. We lay out the bed and overhead speakers, count the channels and subwoofers, then choose the receiver with a channel or two of headroom.
- Zones planned, not discovered. A second zone on a receiver means a second set of speakers on the same box; MusicCast means a second MusicCast device on the network. We decide which before any wire is pulled.
- The network is part of the system. MusicCast rides your existing Wi-Fi, so coverage comes first. Our whole-home Wi-Fi work is done before the first speaker is linked.
- Calibration at the seats. YPAO is a starting point. We run it with the furniture in, listen at the seats people use, and adjust what it got wrong.
- Control and the record. Yamaha’s guides do not describe a control-system driver, so we confirm each exact model’s control port against its manual before promising integration, and the settings go into your project record.
Where Yamaha sits beside the other lines we carry
Yamaha is one of several receiver lines we carry. Denon comes up when the channel count is high in one chassis or HEOS amplifiers are running music through the house; Marantz when the room wants separates or a unit that looks right in the open. Yamaha comes up when the plan is built around MusicCast and YPAO, or when a network stereo receiver or an integrated amplifier is the centre of a listening room. When a house wants many zones from amplifiers in a rack, NAD Electronics is the other place to look.
Common questions
Who installs Yamaha receivers in Kansas City?
IntegrateIT (Overland Park, KS) carries and installs Yamaha audio across the Kansas City metro — media rooms, theaters, listening rooms and whole-house audio in homes on both sides of the state line, from Leawood and Prairie Village to Mission Hills and out to Lee’s Summit. To be precise about the relationship, because the trade is sloppy about this word: Yamaha is a line we carry and install under distribution, not one we hold our own dealer agreement on, so we do not call ourselves an authorized Yamaha dealer. What we do is specify the equipment against the room, wire it, commission it and document it. Phone: (913) 804-7575 or office@integrateit.tech.
Which Yamaha AV receiver fits my room?
Channel count decides it. Yamaha’s guide lists the RX-V4A at 5.2 channels, the RX-V6A at 7.2 and the RX-V8A at 11.2, with Dolby Atmos and DTS:X on all three and a second zone on the RX-V6A and RX-V8A. We count the speakers and subwoofers first and choose the receiver second, with a channel or two of headroom. Yamaha’s guides are the source for these models; we confirm the model on offer and its specification against Yamaha’s documentation when we write the proposal.
What is YPAO?
Yamaha Parametric room Acoustic Optimizer, Yamaha’s room-correction system. Yamaha says it analyzes the acoustics of the room and, on a multichannel receiver, matches the speakers to a chosen target curve; on a two-channel hi-fi receiver it matches the two speakers to each other for imaging and frequency response. It favors cutting frequencies over boosting them. It corrects what the room does to the sound, not where the speakers were put, so we place the speakers first and calibrate second.
How does MusicCast put music through the house?
MusicCast shares music over your existing Wi-Fi network to any MusicCast-enabled component, and a free app controls it from a phone or tablet. Rooms can be played separately or linked, and Routines are whole-home presets. Because it rides the home network, we check Wi-Fi coverage and the network switches before the first device is added, and we decide which rooms use MusicCast devices and which use a second zone from a receiver.
Does Yamaha make a stereo receiver for a listening room?
Yes. Yamaha’s network hi-fi receivers are the R-N600A, R-N800A, R-N1000A and R-N2000A, and its guide names the A-S3200, A-S2200 and A-S1200 integrated amplifiers. The network receivers list MusicCast, Bluetooth and AirPlay 2, and Yamaha’s USB DAC article names the R-N800A, R-N1000A and R-N2000A. We choose between a network receiver and an integrated amplifier by whether the room needs streaming built in, and plan the speakers and the turntable, if there is one, with it.
What happens after the install?
The receiver is calibrated in the room with the furniture in place, the settings are recorded in your portal, and any control-system programming or MusicCast grouping is tested room by room. Our installation carries a five-year workmanship warranty from the final invoice.
Tell us the room and the speakers you want. We will size the receiver.
Or read about home theater · whole-house audio · calibration
Written by Daniel Alon, founder of IntegrateIT LLC, with twenty years in IT and AV integration — Control4 Platinum Dealer, Crestron Elite Partner, Lutron Certified Installer, CEDIA member, HTA Certified. Overland Park, KS.